(Your shopping cart is empty)

  Home > Duct - Flexible / Board / Wrap / Boots > Sound Insulation >

Acoustic Sound Board CASE 4' x 10' Sheets, R4 1", R6 1.5", R8 2"
Acoustic Sound Board CASE 4' x 10' Sheets, R4 1", R6 1.5", R8 2"
 
List Price: $525.00
Our Price: $355.00
You save $170.00!


Availability: Usually Ships in 2 to 3 Business Days
Product Code: 232002


'R' Value (Insulation Thickness)*:


Qty:  
Description
 

Description One 4' X 10' Duct Board CASE

Ductboard has the same insulating/soundproofing qualities as more expensive musical sound dampeners.

NOTE: Freight charges can be very expensive if shipped alone.

Knauf, Owens Corning or equivalent Air Duct Board-AGM is a resin-bonded fiber glass formed into rigid, rectangular boards faced on one side with a fire-resistant foil-scrim-kraft (FSK) vapor retarder and a lightweight fiber glass mat on the airstream surface. Available in EI-475 or EI-800, with a butt edge or a factory-molded shiplap edge, it offers excellent thermal and acoustical performance.

Application

Knauf, Owens Corning or equivalent Air Duct Board-AGM dual-temperature service where good temperature control and noise absorption are required.

Features

  • Low thermal conductivity of 0.23 at 75°F (24°C) mean temperature.
  • Low installed cost,
  • Excellent acoustical characteristics.
  • Non-woven all-glass mat facing on the airstream surface.
  • Assured insulation thickness, shiplap joints, and FSK vapor retarder.
  • If necessary, can be cleaned in accordance with NAIMA's
  • Knauf, Owens Corning or equivalent Air Duct Board systems meet the fire and smoke safety regulations of most federal, state, and local building codes.

Benefits

  • Fabrication in shop environment lowers field installation time.
  • One craft required to fabricate and install system.
  • Minimum capital investment for fabrication equipment.
  • Portability allows for assembly or fabrication at site.
  • AGM facing ensures a smoother airstream surface for a cleaner cut and added durability.
  • Condensation control.
  • Strong thermal performance.

Specification Compliance

In U.S.:

  • ASTM C 1136; Type II (FSK facing)
  • ASTM D 5116
  • ASTM G 21, G 22
  • BOCA
  • CABO
  • California Title 24
  • Corps of Engineers Guide Specifications
  • ICBO
  • International Mechanical Code
  • NFPA 90A and 90B
  • SBCCI
  • UL 181; Class 1

In Canada:

  • CAN/ULC S102-M88
  • CAN/CGSB 51-GP-52M (facing)
  • CAN/CGSB 51.10-92
  • ULC Issue 869C; Class 1

Technical Data

  • UL/ULC listed.
  • Does not exceed 25 Flame Spread, 50 Smoke Developed when tested in accordance with ASTM E 84, CAN/ULC S102-M88, NFPA 255, and UL 723.

Flexural Rigidity

  • Available in two stiffness values: EI-475 and EI-800.
  • Flexural rigidity (EI) is the product of Young's modulus of elasticity (E) and moment of inertia (I) as determined in accordance with NAIMA AHS-100-74.

Service Temperature (ASTM C 411)

  • Up to 250°F (121°C).

Air Velocity (UL 181)

  • Maximum 5000 fpm (1524 mpm).
  • Tested to 12,500 fpm (3810 mpm).

Internal Static Pressure (UL 181)

  • Maximum ±2" water (498 pascals [Pa]).

Water Vapor Permeance (ASTM E 96)

  • Less than 0.02 perms.

Water Vapor Sorption (ASTM C 1104)

  • Less than 5% by weight.

Microbial Growth (ASTM G 21, G 22, UL 181)

  • Does not promote or support the growth of mold, fungi, or bacteria.

Application and Specification Guidelines

Storage

  • Protect stored board from water damage, construction damage, and other abuse.
  • If stored outside, proper protection from weather conditions should be provided.

Application


  • PRESSURE-SENSITIVE TAPES: Only those tapes listed under and imprinted with designation UL 181 A-P and registered with UL.
    HEAT-SEALABLE TAPES: Only those tapes listed under and imprinted with designation UL 181 A-H and registered with UL.
    MASTICS: Mastic systems listed and registered with UL and carrying the designation UL 181 A-M used in conjunction with a 3" (76 mm) wide glass fabric.

Procedures

Notes

This data sheet is not intended to be a design or fabrication manual. For specific details and recommendations on fabrication, reinforcement, hanging, and other details, refer to the latest edition of the NAIMA “Fibrous Glass Duct Construction Standard,” “Residential Standard,” “11/2" Fabrication Manual,” or Knauf, Owens Corning or equivalent Insulation “Air Duct Fabrication Manual.”
Application and installation procedure is at the discretion of and is the responsibility of the Design Engineer to meet specific job requirements.
The chemical and physical properties of Knauf, Owens Corning or equivalent Air Duct Board-AGM represent typical average values determined in accordance with accepted test methods. The data is subject to normal manufacturing variations. The data is supplied as a technical service and is subject to change without notice. References to numerical flame spread ratings are not intended to reflect hazards presented by these or any other materials under actual fire conditions.
SOUND ABSORPTION COEFFICIENTS, 1/3 OCTAVE BANDS (ASTM C 423, TYPE A MOUNTING)
Type 125 Hz 250 Hz 500 Hz 1000 Hz 2000 Hz 4000 Hz NRC
EI-475 1" (25 mm) .03 .25 .62 .89 1.03 .97 .70
EI-800 11/2" (38 mm) .02 .44 .96 1.17 1.16 1.12 .95
EI-800 2" (51 mm) .19 .64 1.08 1.13 1.06 1.06 1.00
FRICTION LOSS (INCHES OF WATER PER 100 FT.)
Air Velocity (FPM) 10" HD 16" HD 24" HD 32" HD 40" HD 72" HD 100" HD
500 .056 .031 .018 .013 .010 .005 .003
600 .080 .044 .026 .018 .014 .007 .004
700 .108 .059 .035 .025 .019 .009 .006
800 .140 .077 .046 .032 .024 .012 .008
900 .176 .096 .058 .040 .031 .015 .010
1000 .216 .118 .071 .050 .038 .018 .012
2000 .845 .463 .278 .194 .147 .071 .048
3000 1.887 1.034 .620 .432 .328 .159 .106
4000 3.340 1.831 1.097 .765 .580 .281 .188
5000 5.206 2.854 1.710 1.193 .904 .438 .293
THERMAL RESISTANCE, R (ASTM C 518) @ 75°F (24°C) MEAN TEMPERATURE
Thickness R-Value R-Value (SI)
1" (25 mm) 4.3 .76
11/2" (38 mm) 6.5 1.14
2" (51 mm) 8.7 1.53
THERMAL CONDUCTIVITY, K (ASTM C 177) @ 75°F (24°C) MEAN TEMPERATURE
k k (SI)
Knauf, Owens Corning or equivalent Air Duct Type EI-475 and EI 800 .23 .033
FORMS AVAILABLE
Thickness Type Size* Edge Pieces/Carton**
1"
(25 mm)
EI-475, EI-800 48" x 96"
(1219 mm x 2438 mm)
Butt, Shiplap 8
1"
(25 mm)
EI-475, EI-800 48" x 120"
(1219 mm x 3048 mm)
Butt, Shiplap 6
11/2"
(38 mm)
EI-800 48" x 120"
(1219 mm x 3048 mm)
Butt, Shiplap 4
2"
(51 mm)
EI-800 48" x 120"
(1219 mm x 3048 mm)
Butt 3
*Other lengths on made-to-order basis. **Palletized packaging on request.



Browse for more products in the same category as this item:

Duct - Flexible / Board / Wrap / Boots > Sound Insulation
Duct - Flexible / Board / Wrap / Boots